How To Repair Plug On Lamp

Over time, the cord effectually the lamp plug may get damaged and stop working. If y'all have a damaged lamp plug, endeavor to replace information technology as soon equally possible to reduce the risk of daze or electric burn. Luckily replacing the old plug only takes a few minutes of work and supplies yous can get from your local hardware store. Exist certain to pay attention to which wires connect to the prongs so you're able to attach them correctly to the new plug.

Stripping the Old Plug and Cord

1. 

   Unplug the lamp from the outlet. Turn off the lamp at the switch for added protection confronting electrical shock. Grab the base of the plug and pull it straight out from the wall outlet. Avert touching the prongs since they may still have a small-scale charge left in them.

   • Never cutting a cord while information technology's yet plugged in, or else you could go seriously injured from electrical shock.
   • If there's damage on the power cord near the plug, wear safe insulated gloves so you don't take to touch any exposed wires.
2. 

   Cutting the one-time plug and i–2 in (2.v–5.one cm) of the cord with a utility knife. To starting time the process of replacing the plug, measure i–2 inches (2.5–5.ane cm) down from the plug and advisedly piece through the cord with a utility knife. Brand the cutting every bit straight as possible and then you lot're less probable to fray the wires. Throw away the old plug as soon as you cut it off.

   • If you take trouble cut the string with a utility knife, endeavour using a pair of scissors instead.
3. 

   Split the wires on the last 1 in (two.5 cm) of the cord. Expect for the thinner section of insulation running through the middle of the lamp cord. Make a ⁄two in (one.iii cm) cutting in the eye of the cord, making certain you don't harm any of the internal wires. Hold onto the each side of the string and gently pull it apart until you split 1 inch (2.v cm).

   • If your lamp cord doesn't accept a thin piece of insulation running downwards the eye, carefully slice through the cord'south insulation to expose 1 inch (2.5 cm) of the wires within of information technology.
4. 

   Remove ⁄2 in (1.3 cm) of insulation off of each wire with wire strippers. Grip one of the wires in the jaws on a pair of wire strippers then it's ⁄ii inch (1.three cm) from the end. Squeeze the handles together to clamp downward on the insulation and pull the strippers toward the end of the cord. Throw away the slice of insulation that comes off of the wire. Repeat the process on the other wire then they're both exposed.

   • If your lamp has a third wire for a grounding port, strip it as well.
5. 

   Twist the frayed ends of the exposed wires so they're easier to attach. Grip the exposed terminate on one of the wires and squeeze together any frayed ends. Rotate them clockwise so they form into a solid wire that doesn't fray. Echo the process for the other wire on the power string.

   • Don't twist the 2 wires together since you won't be able to attach them to the plug.

Wiring the New Plug

1. 

   Become a polarized replacement plug for your lamp. Opt for a replacement plug that has 1 prong that's wider than the other since it provides the most protection against electrical overload. Avoid using non-polarized plugs, or plugs where the prongs take the same width, since they aren't upward to electrical code. Cull a plug that has a similar color to the lamp'south power cord and then it doesn't clash.

   • You can buy polarized replacement plugs from your local hardware shop.
   • If your original lamp plug had a grounding prong, make sure you lot buy a replacement plug with one as well.
2. 

   Unscrew the dorsum cover from the replacement plug. Use a screwdriver to remove the screws holding the replacement plug together. Pull the plastic embrace off of the plug to separate it from the section that contains the prongs and screws. Set the screws bated while yous're working and so y'all don't misplace them.

   • Some replacement plugs have a swivel rather than a comprehend. Remove the screw holding the plug together and pull the sides apart to open up the hinge.
3. 

   Slide the encompass onto the lamp'south cord. Hold the two wires from the lamp together so they're able to fit through the dorsum pigsty of the embrace. Push the cover onto the wires and pull them through to the other side. Proceed the comprehend virtually iii–4 inches (7.half-dozen–ten.ii cm) from the stop of the cord while you work so it doesn't make it the way.

   • If the replacement plug you lot're using has a hinge instead of a split comprehend, you may skip this step.
4. 

   Secure the wire with ribbed insulation to the plug's silvery neutral screw. Look at the insulation on each wire and find the i that has the ribbed edges, which means information technology's the neutral wire. Curve the wire into a pocket-sized claw and put it underneath the argent spiral on the replacement plug's prongs so the wire goes effectually it clockwise. Tighten the spiral with your screwdriver so it firmly presses confronting the wires.

   • The argent spiral connects to the wider prong on a polarized plug, which is the neutral or negative side.
   • If your lamp has three wires, then the neutral wire may have white insulation rather than having a ribbed texture.
5. 

   Hook the wire with the smooth insulation on the plug's brass screw. Locate the wire that has shine edges along the sides of the insulation, and curve the exposed end into a hook. Put the wire underneath the contumely spiral on the side of the replacement plug so it wraps around the screw clockwise. Tighten the screw with your screwdriver then the wire has a business firm connectedness.

   • The brass spiral connects to the smaller prong, which is the "hot" or positive side.
   • If your lamp has 3 wires, then apply the wire that has ruby-red or black insulation.
6. 

   Attach the footing wire to the green screw, if your lamp has one. Look for the light-green wire from the lamp cord and curve a pocket-sized hook shape on the exposed end. Locate the green screw on the replacement plug and constrict the wire underneath it. Tighten the spiral so the wire doesn't come loose.

   • Near household lamps don't have a basis wire, but they may if they are industrial-force lights or employ high-wattage bulbs.
7. 

   Spiral the plug back onto the cover to hibernate the wires. Slide the plastic cover dorsum over the ends of the wires and hold it against the prongs. Check the cord to brand sure none of the exposed wires stick out from the dorsum of the plug. Identify the screws dorsum in the holes and turn them clockwise to tighten them.

   • If you're using a hinged replacement plug, and so guide the cords into the hole at the back of the plug before snapping it closed. Tighten the screw on the plug then it stays closed.
8. 

   Plug in your lamp to test if it turns on. Use an outlet that yous know works then yous know there aren't any other electrical issues preventing the lamp from turning on. Plug the lamp into the outlet and switch it on to see if it lights upward. If it works, then put the lamp dorsum on its original outlet.

   • If the lamp still doesn't work, take apart the plug and check that you continued the wires to the correct screws. Switch them if y'all need to before trying the lamp once again. If it however doesn't piece of work, so there may exist a problem with the lamp'due south bulb socket instead.

Tips

Warnings

• Never work on a lamp plug while it's all the same plugged in since you could daze or electrocute yourself.
• Don't exit any exposed wires outside of the plug because it could increase the risk of shock or fire.

Things Y'all'll Demand

• Utility knife
• Wire stripper
• Polarized replacement plug
• Screwdriver

Source: https://vripmaster.com/14132-replace-the-plug-on-a-lamp.html

Posted by: graypospits.blogspot.com

Share this post